Cryorig CR-H7A Tower Cooler For AMD/Intel CPU
About this deal
Most purchases from business sellers are protected by the Consumer Contract Regulations 2013 which give you the right to cancel the purchase within 14 days after the day you receive the item. We also see that Cryorig ships this cooler with a protective film that has red printing to make it obvious that it needs to be removed. As an effective anti-vibration measure, four rubber dampeners are embedded in the 120mm fan at the corners. Despite the universality of the backplate for other Intel boards, the H7 only supports LGA115x because of the X-bar mechanism.
That being said, I do think the H7 is very good-looking – it has a svelte black top, while the heatpipes have also been covered to make sure there is no unsightly copper on-show. Besides adding the CAM powered RGB system, with the H7 Quad Lumi CRYORIG has added one additional high performance heatpipe as well as increased support enthusiast grade Intel LGA 2011v3. Thanks to its outstanding performance and efficiency, the Cryorig H7 Plus CPU tower cooler is suitable for processors with up to 150 watts TDP (Thermal Design Power). During that period, they have released an extensive lineup of CPU coolers and fans and have quickly made a name for themselves. Installation is straightforward, though at one point you do have to hold the cooler in-place upside-down while tightening the four screws.Enough about the additional accessories, so let’s put them aside until they are required for the actual heat sink installation and the following testing. using the two QF120 balance fans installed in push-pull setup, rotating at maximum speed of 1600 revolutions per minute.
The team of experienced radiator and OC experts uses high-quality materials and novel combinations of individual components to get the most out of air coolers. WCUK Online Ltd is authorized and regulated by the Financial Conduct Authority (FRN 824034) and acts as a credit intermediary. mmH2O, while operating at 330 ~ 1600 ±10 % revolutions per minute range with noise level range of 10 ~ 25 dBA. Where possible, each cooler’s fans are plugged directly into the motherboard using the CPU_Fan or CPU_Opt headers. Based on the original QF120 series the QF120 LED features white LED lighting as well as all of the existing features from the QF series including: Quad Air Inlet™ for added air intake, ultra wide PWM RPM range, integrated Acoustic Absorbers and HPLN™ bearing.Use of these and any missed payments may affect your ability to obtain credit from Klarna and other lenders. It does, of course, ramp up once we overclock the CPU, but even then, the noise is not more than a quiet, steady hum. While installation is not impossible to accomplish solo, this does leave you open to potential slips of the screwdriver and potential damage to the motherboard, or even worse, the potential of somehow dropping the motherboard all together. When idling, it is simply not audible – I put this down the the QF120's fan, which is rated to go as low as 330RPM, give or take 10%.
So let us waste no more time and check the package, the additional accessories, the cooler structure and after that perform some cooling tests. Maintaining the original 145mm height the H7 Quad Lumi is made to fit almost all cases on the market. As the air flows through this section of the cooler, the design squeezes down in size, increasing air-flow as kinking a hose would do to water. Because people have been asking, yes LGA115x covers every single socket including LGA1151, LGA1150 and LGA1156 because the mounting hole distance is exactly the same for all of those models. With direct knowledge of manufacturing and design as well as holding multiple patents under our collective belt, we decided to make a name for ourselves, and that name is CRYORIG.And since this is Cryorig product it features the Hive Fin structure, which combines the Jet Fin Acceleration System and Turbulence Reduction, which means that the fins are designed as a bee hive shaped structure (the loose air intake) on the front side, and normal horizontal position (high density exhaust section) on the back side of the tower. It is also a modestly-sized cooler, measuring just 145mm tall and 98mm long (front to back), including the fan.