Washing Machine / Dishwasher "Y" Piece Hose Splitter

Product Information

Installing waste pipes for washing machines and dishwashers can be done quite simply, but extra-long hoses tend to sag and let stale waster stand in them. See how to connect dishwasher and washing machine to one waste pipe here… Setting Up If the supply pipes run close to the machine, you can simply fit the stop valves and screw the hoses to them. An alternative is to fit self-cutting connectors which contain isolating valves that can be installed without draining the pipes. Pipe Connections If your appliance is built into your kitchen cabinets, then all the connection guidance above will still apply. The key differences are that you’ll need to secure the appliance to the cabinets and attach a decorative door to the front to match your kitchen. Securing the appliance A dishwasher normally just has a cold water supply. The mini stop valve that connects the supply pipe to the machine’s hose lets you isolate the machine without turning off your water. Connect the waste hose to a washing machine trap beneath the sink or use a standpipe with a P-trap. Top tip So I got one from screfix and fitted it as tight as I could with just my hands and straight away it leaked from behind the nut so I used some pliers to tighten it a tiny bit, this seemed to stop the leak so I tried the dishwasher however once it started to draw the water out the water started spraying out. So I tightened it more and more with the pliers and it still wouldn't stop. Eventually I tightened it that much the plastic end broke off.

Usually, a washing machine has hot and cold water pipes extended with T-fittings to reach its supply hoses. Mini stop valves allow you to isolate the machine without having to cut off the water supply. Hook the waste hose into a standpipe with a P-trap. You may need to unscrew the hose from the U-bend under the sink, remembering that this is likely to disconnect your sink waste temporarily too. Consider putting the plug hole stopper in to prevent people from using the sink in the meantime. Clamp the saddle assembly in place around the pipe with its two halves square to the pipe, inserting the screws and tightening them fully. Step 4I've got 1 hot and 1 cold inlet available and the washing machine needs 1 of each however I've recently bought a dishwasher and need to plumb it into the same cold water supply. The problem is the splitter is still leaking, its much better, not spraying water out but its still dripping quite a lot. Does anyone have any suggestions as to what I'm doing wrong here? Should I just try tightening it a bit more with pliers? I know washing machine hoses should be hand tightened as over tightening makes them leak but I am very tempted to just to tighten it another few mm, would you advise this or is there a better option? So like I said earlier you have two main options, I will talk through the pros and cons of both of these below. Washing machine trap with double spigot Yes, I have been running my dishwasher and washing machine off the same waste pipe for over a year now with no problems. It has been used with both machines operating at the same time and again there were no problems. How do you connect a dishwasher to a waste pipe?

To add a second waste (washing machine) to the existing one (sink), a spigot connection is typically required which will mean that the pipework originally taking one incoming pipe is now able to take two. How to connect a washing machine waste pipe Double-spigot trap: Your waste is likely to leave your property through a ‘U bend’ similar to that on your toilet and beneath a sink. This will comprise a piece of vertical pipework, leading to a ‘U bend’ or trap. Double spigot traps are available, where the vertical piece of pipework is replaced with one that allows two connections, or spigots, into it – one being your dishwasher, the other, your washing machine. The appliance should be supplied with the correct fixings to attach the door. Once attached and aligned with the rest of the cabinet doors, ensure you adjust the tension springs in the appliance carcass so that the door opens smoothly and doesn’t slam. Top tip Also, as with all combined drainage systems, cleaner water can help clear the drains of any dirty water. In this case, the ‘grey water’ from your washing machine will help flush out any greases and fats that find their way into your dishwasher waste. A drain hose funnels the waste from your washing machine into the ground. So, when fitting a new washing machine, it is a good idea to learn how to install a washing machine drain hose.

Get your new appliance set up and ready to go

Read on to discover useful tips with sections focusing on how to connect a washing machine waste pipe and how to extend a washing machine drain hose. Connection types for dishwashers and washing machines

If you already have a washing machine plumbed in and want to get a dishwasher too, you’ll want to know if you can use both appliances at the same time – and if you can buy longer hoses and run them under the kitchen cupboards. Washing machines require three different types of connection to function. These are electrical, water and waste. If your washing machine is located near your sink, it can be a wise choice to connect the washer to your sink waste.Obviously, neither of these options was going to work for this lazy sod, so I took to searching for a workaround, and I can happily report that I found a few! There are two main ways to connect a dishwasher and washing machine to one waste pipe, one the proper way and the other the lazy mans way. Needless to say, I went the lazy way… can you connect a dishwasher and washing machine to one waste pipe Connecting dishwasher and washing machine to one waste pipe Finally, pull the drain below the level of where the water is sat – this will likely have a siphon effect that will start to clear the water.