Cisco 10GBASE-SR SFP Module for 10-Gigabit Ethernet Deployments, Hot Swappable, 5-Year Standard Warranty (SFP-10G-SR=)

Product Information

The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices. The GLC-BX80-D-I and GLC-BX80-U-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. The GLC-GE-DR-LX SFP can interoperate with other 100M SFPs/interfaces as long as those are based on 100BASE-LX10 standard. A 5dB attenuator is needed on the path of dual-rate SFP Tx and 100BASE-LX10 interface Rx. No attenuator is needed on the other fiber strand. For S-Class SFP+ 10 Gigabit Modules, refer to the link below: https://www.cisco.com/c/en/us/products/interfaces-modules/transceiver-modules/datasheet-listing.html. Compared with Cisco C-class modules which can be operating with three different temperature ranges, the Cisco S-class modules can only support the commercial temperature ranges which is 0 to 70°C (32 to 158°F). The Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz *km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz *km MMF (OM4), up to 400m link lengths are possible.

The GLC-BX-D and GLC-BX-U SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. The Cisco SFP-10G-SR is in full compliance with the 10G BASE-SR standard. This module has a link length of 26m on the most commonly used standard FDDI- grade multimode fiber. FDDI stands for Fiber Distributed Data Interface. It supports a link length of 300m over OM3 cables and a link length of 400m over OM4 cables. Information about Cisco’s environmental sustainability policies and initiatives for our products, solutions, operations, and extended operations or supply chain is provided in the “Environment Sustainability” section of Cisco’s Corporate Social Responsibility (CSR) Report. When shorter distances of Single-Mode Fiber (SMF) are used, it might be necessary to insert an inline optical attenuator in the link to avoid overloading the receiver. A 10-dB inline optical attenuator should be inserted between the fiber-optic cable plant and the receiving port on the SFP at each end of the link whenever the fiber-optic cable span loss is less than 8 dB. The Cisco SFP-10G-LR-X is a multirate 10GBASE-LR, 10GBASE-LW, and OTU2/OTU2e module for extended operating temperature range. It supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF,G.652).A SFP-10G-BXD-I device is always connected to a SFP-10G-BXU-I device with a single strand of standard SMF with an operating transmission range up to 10 km. Hard drive retention: Hard drive retention is not available on models with a soldered hard drive, including XPS 9315 2in1, Chromebooks or Venue tablets, except the Venue 11 Pro.

The Cisco 10GBASE-LR Module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF, G.652). The Cisco 10GBASE-SR module supports a link length of 26 meters on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000 MHz *km MMF (OM3), up to 300-meter link lengths are possible. Using 4700 MHz *km MMF (OM4), up to 400 meter link lengths are possible. SFP-10G-SR-S does not support FCoE. The SFP-10G-BXD-I and SFP-10G-BXU-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.

{{-labels.sendtoColleague}}

To begin with, 10G SFP+ optical transceivers are easily available in the market and are now a mature technology. They are not too expensive. 40G/100G optical modules are commonly used in data centres and enterprises around the world for interconnection. The 10G SFP+ modules have many different standards such as SFP-10G-LR, SFP-10G-SR, 10GBASE-LRM SFP+ and 10GBASE-ER SFP+. We have focused on the factors that separate SFP-10G-SR from SFP-10G-LR. The Cisco SFP-10G-LR module is capable of working with a link length of 10 km on any basic single-mode fiber. It is completely in compliance with the 10G Base-LR standard and uses 1310nm lasers. The LR module has no minimum distance, which is why it is ideal for short connections carried over a single mode fiber. The 1000BASE-BX-D and 1000BASE-BX-U SFPs, compatible with the IEEE 802.3ah 1000BASE-BX10-D and 1000BASE-BX10-U standards, operate on a single strand of standard SMF. The Cisco SFP-10G-LR-X is a multirate 10GBASE-LR, 10GBASE-LW, and OTU2/OTU2e module for extended operating temperature range. It supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF, G.652).

Cisco only published four 10G S-class SFP+ modules and two 40G S-class QSFP+ modules. The following table listed Cisco S-class modules. Cisco S-class modules seem to have no differences from the non-S-class modules. However, if you read the specification of these modules and the suggestions from Cisco, you will find the differences. The Cisco SFP-10G-ZR-I is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module for industrial operating temperature range. The SFP-10G-ZR-I has a limiting electrical interface receiver, which does not require EDC PHY on the host board, it can be plugged into any SFP+ port. It supports link lengths of up to 70 kilometers on standard Single-Mode Fiber (SMF, G.652), assuming a fiber chromatic dispersion of 20ps/(nm *km). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications. The SFP-10G-ZR-I has a cold start at -40⁰C; the transceiver will be operational except optical traffic is not supported from -40⁰ to -28⁰C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational from -28⁰C to 85⁰C. The Cisco 10GBASE-LRM Module also supports link lengths of 300m on standard Single-Mode Fiber (SMF, G.652).Terms Apply. Promotion ends 3 December 2023. Items are subject to availability. Max 5 units per customer. The GLC-GE-DR-LX SFP also supports Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. The Cisco 10GBASE-LR module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF) (G.652). SFP-10G-LR-S does not support FCoE. The Cisco 10GBASE-LRM Module supports link lengths of 220m on standard Fiber Distributed Data Interface (FDDI) grade Multimode Fiber (MMF). To make sure that specifications are met over FDDI-grade, OM1 and OM2 fibers, the transmitter should be coupled through a mode conditioning patch cord. No mode conditioning patch cord is required for applications over OM3 or OM4. For additional information on mode conditioning patch cord requirements please see: https://www.cisco.com/en/US/prod/collateral/modules/ps5455/product_bulletin_c25-530836.html. The Cisco 10GBASE-LR Module supports a link length of 10 kilometers on standard Single-Mode Fiber (SMF,G.652).

The Cisco SFP-10G-SR series has 2 other important modules: the Cisco SFP-10G-SR-X Module and the Cisco SFP-10G-SR-S Module. While the Cisco SFP-10G-SR-S module is a part of the Cisco S-class optics it matches the Cisco SFP-10G-SR module in performance. The Cisco 10GBASE-ER Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652). The SFP-10G-ZR-I has a cold start at -40 ⁰ C, the transceiver will be operational except optical traffic is not supported from -40 ⁰ C to -28 ⁰ C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational -28 ⁰ C to 85 ⁰ C. The Cisco 1-Gbps SFPs are supported across a variety of Cisco networking equipment *. For more details, refer to the document SFP Compatibility Matrix at: https://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.pdfThe communication over a single strand of fiber is achieved by separating the transmission wavelength of the two devices. The GLC-BX40-D-I, GLC-BX40-DA-I, and GLC-BX40-U-I SFPs also support Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. LRM transceivers are often mistaken for 10GBASE-LR SFP+ optics, but it is not the same. 10GBASE-LRM SFP+ makes use of the 1310nm lasers, however, it has a maximum reach of only 220 m over standard multimode fibers such as OM3/OM4. This transceiver is available in the XFP and SFP+ form factors. A GLC-BX80-D-I device is always connected to a GLC-BX80-U-I device with a single strand of standard SMF with an operating transmission range up to 80 km.